Forklift Drive Motors

Drive Motor for Forklifts - MCC's or otherwise known as Motor Control Centersare an assembly of one or more sections that include a common power bus. These have been used in the vehicle business since the 1950's, because they were made use of lots of electric motors. Now, they are used in different industrial and commercial applications.

Inside factory assembly for motor starter; motor control centers are quite common method. The MCC's include programmable controllers, metering and variable frequency drives. The MCC's are normally used in the electrical service entrance for a building. Motor control centers often are utilized for low voltage, 3-phase alternating current motors that range from 230 volts to 600 volts. Medium voltage motor control centers are intended for big motors which range from 2300V to 15000 V. These units use vacuum contractors for switching with separate compartments so as to attain power switching and control.

In areas where really dusty or corrosive processes are taking place, the motor control center can be installed in a separate air-conditioned room. Normally the MCC would be positioned on the factory floor next to the machinery it is controlling.

For plug-in mounting of individual motor controls, A motor control center has one or more vertical metal cabinet sections with power bus. To complete testing or maintenance, really large controllers could be bolted into place, whereas smaller controllers can be unplugged from the cabinet. Every motor controller consists of a contractor or a solid state motor controller, overload relays to protect the motor, circuit breaker or fuses to provide short-circuit protection as well as a disconnecting switch in order to isolate the motor circuit. Separate connectors allow 3-phase power to be able to enter the controller. The motor is wired to terminals positioned in the controller. Motor control centers supply wire ways for power cables and field control.

Every motor controller inside a motor control center can be specified with different choices. These choices include: control switches, pilot lamps, separate control transformers, extra control terminal blocks, as well as many kinds of bi-metal and solid-state overload protection relays. They even comprise different classes of kinds of power fuses and circuit breakers.

There are a lot of options regarding delivery of MCC's to the client. They can be delivered as an engineered assembly with interlocking wiring to a central control terminal panel board or programmable controller along with internal control. On the other hand, they can be supplied set for the customer to connect all field wiring.

Motor control centers normally sit on the floor and must have a fire-resistance rating. Fire stops could be required for cables that go through fire-rated floors and walls.

Click to Download the pdf

Forklift Parts

Forklift Fuel Systems

Fuel Systems for Forklifts - The fuel systems task is to supply your engine with the diesel or gasoline it requires to be able to function. If whatever of the fuel system parts breaks down, your engine will not run right. There are the major parts of the fuel system listed underneath: Fuel Tank: The fuel tank holds the fuel....

More

---

Parts for Industrial Scissor Lift

Industrial Scissor Lift Parts - The scissor lift or table lift, is an automated industrial lift that has been tailored to be used in retail, wholesale, manufacturing and production environments. Industrial scissor lifts have been used chiefly within production and manufacturing facilities for many decades to successfully hoist and lower supplies, people and other equipment. The scissor lift is a...

More

---

Drive Unit for Forklifts

Drive Unit for Forklifts - Instead of a transmission, a hydraulic pump is powered by the forklift motor. Hydraulic power from the pump is supplied to hydraulic drive motors which are connected to all the drive wheels so as to provide power to the lift truck.

More

---

Parts for High Reach Forklifts

High Reach Forklift Parts - Forklifts are utilized in practically all warehouse operations and in boat yards and in industrial construction sites. The reach feature of a lift truck is a very important part utilized in various applications such as whenever a shelving system is being utilized to stack pallets. A lift truck operator will utilize the machine's reach feature...

More

---

Forklift Chain

Chains for Forklift - The life of lift chains on lift trucks can be extended greatly with proper maintenance and care. Like for instance, correct lubrication is actually the most efficient method to be able to prolong the service capability of this part. It is really essential to apply oil occasionally utilizing a brush or other lube application device. The...

More

---

Forklift Starter and Alternator

Forklift Starter and Alternator - The starter motor these days is usually either a series-parallel wound direct current electric motor that consists of a starter solenoid, that is similar to a relay mounted on it, or it can be a permanent-magnet composition. As soon as current from the starting battery is applied to the solenoid, mainly via a key-operated switch,...

More

---

Part for Electric Forklift

Parts for Electric Forklift - Utilizing a charging stations is the most common way to charge an electric lift truck battery. The charging station would connect along with the battery by utilizing two 8-foot cords. Newer models are equipped along with an automatic charge shut off. This charges the battery hard for 6 hours, next at a lower level for...

More

---

Barrel Clamps

Barrel Clamps - A Barrel Clamp is actually a hydraulic or mechanical attachment for a lift truck. It can be used so as to squeeze the item you would like to transfer using the lift truck and is usually utilized for handling paper rolls, barrels, and kegs. A few designs of barrel clamp attachments even have a revolving function. For...

More

---